Airman AX40 Hydraulic Final Drive Motor

E:mm; Pu:98.680 kN; b1:mm; D:260 mm; Dynamic (Ca):810 kN; Static (Coa):981 kN; rs (min):3 mm; d2 (max):mm; B:86 mm; r1s (min):3 mm;

Spring washer in accordance with DIN 128:A 20; B:45 mm; Hexagonal head bolt:M 20x40; M:21 mm; M2:54 mm; M3:22 mm; M1:7 mm; Mass locking clip:0.22 kg;

Basic Static Radial Load Rating Co:365000 N; Oil Speed Rating Open/Shielded n2:1300 rpm; Basic Dynamic Radial Load Rating C:242000 N; Sealed Speed Rating n3:0 rpm; B:46.00 mm; Fillet Radius ra:2.00 mm; d:380.000 mm; D:480.0000 mm; Accessories:Two Seals; Grease Speed Rating Open/Shielded n1:1000 rpm;

Fillet Radius ra:2.00 mm; Basic Dynamic Radial Load Rating C:119000 N; Accessories:One Seal; Basic Static Radial Load Rating Co:132000 N; B:33.00 mm; d:180.000 mm; D:250.0000 mm; Oil Speed Rating Open/Shielded n2:2800 rpm; Sealed Speed Rating n3:1500 rpm; Grease Speed Rating Open/Shielded n1:2200 rp

Grease Speed Rating n1:2000 rpm; D:180.0000 mm; Basic Static Radial Load Rating Co:166000 N; B:60.30 mm; Sealed Speed Rating n3:2000 rpm; Basic Dynamic Radial Load Rating C:178000 N; Oil Speed Rating n2:3000 rpm; Fillet Radius ra:2.00 mm; Accessories:One Shield & Snap-Ri; d:100.000 mm;

Cap bolt, SAE grade:8; H1:95.25 mm; da:76.2 mm; A1:88.9 mm; End plug (suffix Y):EPR 9; J min.:250.825 mm; Pa:9.25 kN; P60°:78.7 kN; S:4.763 mm; PG:1/8 NPT;

d2 ≈:65.263 mm; d:55 mm; D2 ≈:90.45 mm; Calculation factor kr:0.025; Fatigue load limit Pu:1.25 kN; Da max.:91 mm; Mass bearing:0.6 kg; Basic dynamic load rating C:46.2 kN; ra max.:1.5 mm; D:100 mm;

db min.:63.5 mm; Cb min.:4 mm; ra max.:3.5 mm; T:20.638 mm; Calculation factor e:0.31; Da min.:80 mm; r1,2 min.:3.5 mm; Da max.:81.5 mm; da max.:58 mm; Fatigue load limit Pu:10.4 kN;

Radial shaft seal with a low cross-sectional height, double lip:SD 18x24x3; Basic dynamic load rating C:16.1 kN; D:24 mm; Inner ring IR series:IR 15x18x16.5; Fw:18 mm; C:16 mm; Limiting speed:14000 r/min; Mass bearing:0.02 kg; Radial shaft seal with a low cross-sectional height, single lip:G 18x24x3

Basic Dynamic Radial Load Rating C:55900 N; d:65.000 mm; Basic Static Radial Load Rating Co:40500 N; Grease Speed Rating n1:5300 rpm; B:23.00 mm; Oil Speed Rating Open/Shielded n2:6300 rpm; D:120.0000 mm; Oil Speed Rating n2:6300 rpm; Sealed Speed Rating n3:3600 rpm; Grease Speed Rating Open/Shielde

Basic dynamic load rating C:680 kN; D:139.7 mm; Design (sliding contact surface combination):Steel/steel, heavy-d; Specific dynamic load factor K:100 N/mm²; dk:128.016 mm; Mass plain bearing:4.8 kg; ra max.:0.6 mm; r1 min.:0.6 mm; Material constant KM:330; B:77.775 mm;

D:37.0000 mm; Basic Static Radial Load Rating Co:2900 N; Basic Dynamic Radial Load Rating C:4360 N; Fillet Radius ra:0.30 mm; B:7.00 mm; Accessories:One Seal; Oil Speed Rating Open/Shielded n2:20000 rpm; Grease Speed Rating Open/Shielded n1:17000 rpm; d:25.000 mm; Sealed Speed Rating n3:11000 rpm;

Grease Speed Rating n1:1100 rpm; D:480.0000 mm; Basic Static Radial Load Rating Co:900000 N; Fillet Radius rb:1.50 mm; B:74.00 mm; Fillet Radius ra:3.00 mm; d:320.000 mm; Basic Dynamic Radial Load Rating C:527000 N; Oil Speed Rating n2:1400 rpm;

D:87.312 mm; Dimension series:3500; Ca min.:4 mm; B:30.886 mm; T:30.162 mm; Reference speed:6300 r/min; r3,4 min.:3.3 mm; Da min.:73 mm; Mass bearing:0.78 kg; Db min.:80 mm;

SWN:7 mm; Basic dynamic load rating C:43.6 kN; Fatigue load limit Pu:1.25 kN; Housing material:Cast iron; Basic static load rating C0:29 kN; A5:29.5 mm; T:64.4 mm; N:18 mm; GN:1/4-28 SAE-LT; J6:154 mm;